resistance brazing
英 [rɪˈzɪstəns ˈbreɪzɪŋ]
美 [rɪˈzɪstəns ˈbræzɪŋ]
网络 电阻钎焊
双语例句
- The influence of annealing and processing conditions on the mechanical property and sagging resistance of the brazing sheet is investigated in this paper.
研究了高频钎焊铝管用硬钎焊带退火工艺对材料力学性能、耐下垂性能的影响。 - Milling, planing, impact and percussion. High toughness for medium wear resistance. Well suitable for brazing.
铣削、刨平、挤压和冲击操作。在中等磨损条件下具有高的韧性。很适合硬焊。 - Effect of annealing process on sagging resistance ability of brazing aluminium foil
退火工艺对钎焊铝箔抗下垂能力的影响 - Study on micro-performance of resistance brazing joint of Ti and Cu
Ti-Cu电阻钎焊接头微观性能研究 - Resistance Heating Brazing with Molybdenum Electrode
钼电极电阻加热硬钎焊 - Research on the Wear Resistance of WC-Co WC-Ni WC Brazing Coatings
WC-CoWC-NiWC钎焊涂层耐磨性研究 - Because the property of niobium alloy is far from that of stainless steel, some special welding techniques have been applied, such as explosive welding, vacuum braze welding, electric resistance welding, vacuum electron beam self-material brazing and so on.
因为二者的性能差别较大，所以通常采用一些特殊的方法进行焊接，如爆炸焊、真空钎焊、电阻焊和真空电子束自钎焊等。 - Resistance brazing for joints within rotor coils of big generator
大型发电机转子线圈接头电阻钎焊 - A Resistance Brazing Process for Brazing Rocker Arms of Engine Oil Pumps
机油泵摇臂支架电阻钎焊工艺 - The resistance brazing principle; the selection of brazing parameters and quality control measures are introduced for the lap joints of copper strip rotor coils within big electrical generator.
介绍了大电机紫铜带线圈斜搭接接头电阻钎焊装置工作原理、参数选择以及钎焊质量的控制。 - The brazing technics of the EGR cooler and corrosion resistance of the joint, with three brazing filler metal-copper, BNi-2, BNi-7 brazing 316L stainless steel, is discussed in this paper.
本文主要研究三种钎料-纯Cu、BNi-2和BNi-7钎焊316L不锈钢的钎焊工艺及钎焊接头的耐腐蚀能力。 - Technology of dissipation heat resistance brazing for polycrystalline diamond cutting teeth the study to measure micro-ohm resistance
聚晶金刚石切削齿散热电阻钎焊工艺的研究小电阻测量技术 - A new method to improve the heat resistance of the brazing seam
提高钎缝耐热性的新途径 - Resistance Brazing and Its Application
电阻钎焊及其应用 - Wear Resistance and Abrasion Mechanism of Hard Alloy Particles Reinforced Composite by Brazing Process
钎焊法制备硬质颗粒复合材料的耐磨性和磨损机理 - Thermal cycle resistance of Al2O3/ Ni-Ti/ Kovar joints was studied, which were prepared by active brazing technique. The experimental results show that the joint shear strength increases after 200~ 600~ 200oC thermal cycles.
对采用活性钎焊的Al2O3/Ni-Ti/Kovar（可伐）接头进行了考察，实验结果显示，接头经热循环后强度异常增加。 - Design and reliability of the micro-controller of resistance brazing
电阻钎焊微控制器设计与可靠性研究 - The effect of different hardmetal powders on the wear resistance of brazing coating was studied and the wear mechanism of the coating was analyzed.
研究了不同硬质合金粉对钎焊涂层抗磨料磨损性能的影响，初步分析了涂层磨损机制。 - Resistance Brazing of Copper With Carbon Steel, Phosphor Bronze or Brass
紫铜与碳钢、锡磷青铜、黄铜的电阻钎焊 - Rare earth elements Y, Ce can refine grains and change structural distribution condition, and increase the mechanical properties and corrosion resistance of brazing joints, but can not change electrode potential of the brazing filler metals.
稀土Y、Ce能细化晶粒，改变组织的分布状态，不改变钎料的电极电位，但却提高了钎焊接头的机械性能和抗腐蚀性。 - Study on Wear Resistance of WC/ Cu-Mn-Ni Brazing Coating Under Dry Sliding
干摩擦条件下WC增强Cu-Mn-Ni复合涂层的磨损性能研究 - Because of excellent performance of resistance to intergranular corrosion due to the low carbon content, 316L stainless steel is widely used in the brazing technology for heat exchangers, coolers and other corrosion-resistant parts.
316L不锈钢因含碳量低，具有优良的耐晶间腐蚀性能，广泛用于制造热交换器、冷却器等耐腐蚀钎焊部件。